防火彩钢板隔墙应用的方法有哪些
1防火彩钢板：一般建议采用厚度大于6mm的镁板作为阻隔板。
2
防火彩钢板附件：将直径大于6mm的钢板固定在框架边缘，用3.5200mm沉头螺钉固定，并用比沉头面低0.5mm的钉头找平。
三。安装：在安装开始时，应将龙骨的位置和标记正确。纵龙骨中心距450-600mm。墙与门窗两侧连接处安装时，应加设龙骨。如墙高大于2440mm时，必须在板的连接部位安装支撑龙骨。
4
防火彩钢板板间距：相邻板之间有4-6 mm的间隙，板与地面之间要求有5 mm的间隙。螺钉安装中心距为150mm，距板边10mm，距板角30mm。
5吊装：卫生间、厨房等起吊物应采用钢板或龙骨加固，以免损坏钢板。
6接缝理：安装时板与板之间有间隙。用4-6mm、107胶或强力胶调好后，用刮刀刮平板缝，用胶带或纸带粘贴压脚。
7涂层装饰：喷涂、刷子或刷子。刷子必须参照油漆说明书。
8
防火彩钢板装饰砖：在卫生间、卫生间、厨房、地下室等潮湿区域设置时，瓷砖龙骨在板面上的距离应缩短至400mm。墙上每3块板（约3.6mm）应有伸缩缝。
9隔声墙：当墙体需要较高的隔声效果时，应将墙与板紧密封闭，空墙应填充矿棉。例如，龙骨两侧采用两块不同厚度的钢板，分隔效果更好。
10抗冲击墙身：建议选用8mm以上的防火板或加强板。下一块必须用长螺丝加固。这种方法可以提高冲击、隔热、隔音和防火性能。
1. Fireproof board: it is generally recommended to use magnesium plate with thickness of more than 6 mm as barrier plate.
2. Accessories: the plate with a diameter of more than 6 mm is fixed on the edge of the frame, fixed with a 3.5200 mm countersunk screw, and the finish surface is leveled with a nail head 0.5 mm lower than the countersunk surface.
3. Installation:
at the beginning of installation, the correct position and mark of keel should be made. The center distance of longitudinal keel is 450-600mm. When it is installed at the connection part of wall and both sides of doors and windows, additional keel shall
be installed. For example, when the height of the wall is greater than 2440 mm, the supporting keel must be installed on the connection part of the plate.
4. Distance between plates: there is a gap of 4-6 mm between adjacent plates, and a gap of
5 mm is required between plates and the ground. The installation center distance of screws is 150 mm, 10 mm from the edge of the plate and 30 mm from the angle of the plate.
5. Hoisting: toilet, kitchen and other lifting objects should be reinforced
with plates or keels to avoid damaging the plates.
6. Joint treatment: there is a gap between the plate and the plate during installation. After adjustment with 4-6mm, 107 adhesive or strong adhesive, apply scraper to the plate and gap, and paste
the presser foot with tape or style tape.
7. coating decoration: spray, brush or brush. Brush must refer to the instructions of the paint.
8. Decorative tile: when it is set in the bathroom, toilet, kitchen, basement and other humid areas,
the distance of tile keel on the board surface should be shortened to 400mm. There should be expansion joints on every 3 boards (about 3.6 mm) on the wall.
9. Sound insulation wall: when the wall needs a higher sound insulation effect, the wall
and the board should be tightly closed, and the empty wall should be filled with mineral wool. For example, when two different thickness plates are used on both sides of the keel, the separation effect is better.
10. Impact resistant wall body:
it is recommended to select fireproof board or reinforcing plate of 8mm or above. The next block must be reinforced with long screws. This method can improve the impact, heat insulation, sound insulation and fire resistance.
