谨记以下几点决定彩涂卷的使用寿命
使用彩涂卷时应注意以下几点，防止彩涂辊损坏，降低使用寿命。
1.装卸过程中，起重机与
彩涂卷接触处应加橡胶垫，防止划伤和油漆脱落。
2.当
彩涂卷需要纵向切割时，应在与彩涂板接触的设备地面上铺设橡胶垫。切割后，应立即清除切割的金属屑，以防止划伤彩色涂层板表面的涂层。
3.锌可用作保护钢。在使用彩色涂层钢板的隐蔽位置，有严格的工程要求尽可能保护切口。
4.本工程安装完成后，在施工过程中应检查并清除彩涂板上的残余焊点和金属屑，避免对彩卷造成腐蚀。彩色涂层辊必须存放在干燥通风的室内环境中，避免露天存放在容易冷凝和温度变化的区域。如果在模压成型过程中需要覆盖薄膜，如PVDF涂层彩色涂层板和铝锌涂层轻型板。
5.
彩涂卷应存放在干净整洁的环境中，防止各种腐蚀介质的侵蚀。储存区的地面应平整，不坚硬，并具有足够的承载力。
6.水平钢卷应放置在橡胶垫、垫木、支架等装置上，紧固件不得向上放置，应直接放置在地面或运输工具上。
7.为防止压碎，钢卷不得重叠存放。堆放钢板时，应严格限制堆放层数，重量和尺寸较大的包装应放在下层。
8.在建筑物表面使用
彩涂卷时，尽量在同一厂家的同一条生产线上同时生产，避免因混色造成色差，影响视觉效果。
The ollowing points shall be paid attention to when using the color coating roll to prevent the damage of the color coating roll and reduce the service life.
1. During loading and unloading, rubber pads shall be added at the contact between the crane and the color coating roll to prevent scratches and paint falling off.
2. When the color coating roll needs to be cut longitudinally, a rubber pad shall
be laid on the ground of the equipment in contact with the color coating plate. After cutting, the cut metal chips shall be removed immediately to prevent scratching the coating on the surface of the color coated plate.
3. Zinc can be used as protective
steel. As far as possible, there are strict engineering requirements to protect the incision at the hidden position where the color coated plate is used.
4. After the installation of the project, check and remove the residual welding points and
metal chips on the color coated plate during construction to avoid corrosion to the color coil. The color coating roll must be stored in a dry and ventilated indoor environment to avoid open storage in areas prone to condensation and temperature change.
If it is necessary to cover film during press molding, such as PVDF coated color coated plate and aluminum zinc plated light plate.
5. The color coating roll shall be stored in a clean and tidy environment to prevent the erosion of various corrosive
media. The floor of the storage area shall be flat, not hard and with sufficient bearing capacity.
6. The horizontal steel coil shall be placed on the rubber pad, skid, bracket and other devices, and the fasteners shall not be placed upward, but
directly on the ground or transportation tools.
7. In order to prevent crushing, steel coils shall not be overlapped for storage. When stacked steel plates are stored, the number of stacked layers shall be strictly limited, and packages with large
weight and size shall be placed in the lower layer.
8. When the color coating roll is used on the surface of a building, try to produce products on the same production line of the same manufacturer at the same time to avoid color difference caused
by mixing and affecting the visual effect.
