彩涂板施工过程细节控制

天物集团专注彩涂卷行业17年——彩涂板施工过程细节控制_彩钢板生产施工一站式服务请拨打网站上方电话咨询

安装过程中，加强现场管理，严格控制各工序。
檩条安装必须拉线找平，否则彩钢板将承受荷载，部分檩条为虚檩条，固定螺钉将根据檩条高度而定
不同程度地拉动和折叠色板。

装固定螺钉时应用力适当，不得偏斜，使防水垫圈失去防水功能。屋面螺丝及扣件处理采用10C×10cm宽防水层。
修剪是为了更有效地防止雨水进入屋顶。当车顶外板位于屋脊处时，使用封边工具将钢板端子处的彩板转向车顶
折叠起来，以确保防水板或盖板下的风吹入的水不会流入建筑物。在屋檐下端，钢板端部略微向下弯曲（唇形），在钢板端部形成向下折边，以保证雨水沿钢板端部排出，不受毛细管或风的影响
力返回到屋顶板的下边缘。轮廓板具有相应的成型泡沫密封条，该成型泡沫密封条嵌入在屋檐支撑面和顶板下侧之间。
（用作屋檐密封）。将饰条沿泛水板下部和盖板插入泛水板下部和车顶板顶面之间，并使用双面胶带
适当固定，以便起到类似的密封作用。
对于单层彩板房屋，为了减少太阳辐射到建筑物中的热量，在安装屋顶板时，可以在屋顶系统中安装隔热层
层安装车顶钢板前，在檩条或条带上铺设双面反光箔膜。这种方法也可用作蒸汽隔离，以减少
少凝结。为了减少屋面钢板下的结露，必须在钢板下设置防潮板，防止钢板下表面与空气之间受潮
联系如果建筑物内发生冷凝，消除其不利影响既困难又昂贵。因此，在设计和施工中
采取预防措施。为了避免屋顶上的水凝结，必须防止湿空气接触钢板下方。用于反射箔层和屋顶
在钢板之间放置隔热棉的方法将进一步避免水分的侵入。当使用隔热棉层时，必须注意使其完全防潮。特别是
在屋顶边缘周围和钢板终端底部，如果是小坡度屋顶，雨水可能会被吹回。如果绝缘棉悬挂在底部支架上
在表面上方，它可能与排水沟中的水接触。在这种情况下，隔热棉将吸收水分，并在潮湿气候下长时间保持水

在隔热棉中，由于与湿隔热棉接触，这将损坏车顶板涂层。

During installation, strengthen site management and strictly control each process.

Purlins must be installed by pulling through the line and leveling, otherwise the color steel plate will bear the load, some purlins are virtual, and the fixing screws will be due to the height of the purlins

Pull and fold the color board with different degrees.

The fixing screw shall be installed with proper force and shall not be biased, so that the waterproof washer will lose its waterproof function. 10C is adopted for the treatment of roof screws and fastenersm × 10cm wide waterproof layer.
Trimming is to more effectively prevent rainwater from entering the roof. When the roof outer plate is at the ridge, use the edge closing tool to turn the color plate at the steel plate terminal towards the roof
Fold up to ensure that the water blown in by the wind under the flashing or cover plate will not flow into the building. At the lower end of the eaves, the end of the steel plate shall be bent slightly downward(lip shape), a downward folded edge will be formed at the end of the steel plate, so as to ensure that the rainwater will be discharged along the end of the steel plate and will not be caused by capillary or wind
The force returns to the lower edge of the roof slab. The contour plate has a corresponding molding foam sealing strip, which is embedded between the eaves supporting surface and the lower side of the roof panel.
(used as eaves seal). Insert the molding strip between the lower part of the flashing plate and the top surface of the roof panel along the lower part of the flashing plate and the cover plate, and use double-sided adhesive tape

Proper fixing, so as to play a similar sealing role.

For a single-layer color plate house, in order to reduce the heat radiated by the sun into the building, when installing the roof panel, heat insulation can be installed in the roof system

Layer. Before installing the roof steel plate, lay double-sided reflective foil film on the purlin or strip. This method can also be used as steam isolation to reduce

Less condensation. In order to reduce condensation under the roof steel plate, a moisture-proof plate must be set under the steel plate to prevent moisture between the lower surface of the steel plate and the air

Contact. If condensation occurs in buildings, it is difficult and costly to eliminate its adverse effects. Therefore, in the design and construction

Take precautions. In order to avoid water condensation on the roof, wet air must be prevented from contacting under the steel plate. Used in reflective foil layer and roof

The method of placing heat insulation cotton between steel plates will further avoid the invasion of moisture. When thermal insulation cotton layer is used, care must be taken to keep it completely moisture-proof. Especially for

Around the edge of the roof and at the bottom of the steel plate terminal, in the case of a small slope roof, the rainwater may be blown back. If the insulation cotton is suspended on the bottom support

Above the surface, it may be in contact with the water in the gutter. In this case, the heat insulation cotton will absorb water and retain the moisture for a long time during humid climate

In the insulation cotton, this will damage the roof panel coating due to contact with wet insulation cotton.