天物彩板专注彩板16年——更多彩钢板特性_机房防火彩涂板定制_天物粉末喷涂彩板请拨打网站上方电话咨询

一、彩钢板特性

1。机房彩钢板由0.6mm热镀锌钢板和12mm耐火石膏内装饰板组成。机房彩钢板饰面为多组分聚酯硬化涂料，含导电组分。通过增大导电系数和减小静载荷，表面电阻值为105-8，电荷衰减小于1秒。采用静电烤漆喷涂工艺，表面光滑、细腻、无尘、易于维护，极大地保证了机房的清洁要求。

2。机房彩钢板符合国家标准一级防火标准，完全能满足机房施工及装修的防火要求。
3。机房彩钢板表面为彩钢板，防潮、防霉、耐酸碱、抗静电。500Hz时隔声率可达45dB（500Hz产生的噪声一般为118db），加权隔声的改善相当高。
4。机房彩钢板孔隙率高，均为微孔，导热系数小[一般为0.121~0.205w/（m.k）），热容大，吸湿性强，对调节室内温度有一定作用。
5。机房彩钢板隔室系统满足cns12514-5kg跌落冲击试验要求，抗冲击能力强。
6。机房彩钢板安装周期短，场地清洁，为整个工程节省了宝贵的施工时间。机房内彩钢板可拆卸修复，方便拆装、水电维修、线路改造等。
7。可在机房彩钢板墙上打孔，不需额外处理，安装控制开关、电源插座等设备非常方便。表面色彩柔和，与地板、天花板形成统一和谐的整体，使整个空间具有现代气息
彩钢板在机房建设中的作用是什么？
二。彩钢板使用场所
A.国家部委办公楼；政府机构；银行、保险、证券等金融机构的计算机中心；高端办公楼。
B.公共空间医院；学校；科研院所；民航、地铁等交通站点。
C.工业建筑标准化工业厂房；食品、药品、化工等厂房；专业实验室或研发中心。
D.商业空间展示中心；运动场馆；星级酒店
机房壁板安装时应注意以下几点
1。机房壁板安装时使用专用工具，施工人员在施工过程中
检查前，检查工具是否齐全。检查的具体工作是主要材料和附件是否齐全，是否可以使用。专用量具应经检验后定做。不符合使用要求的，应当及时更换、修理。
2。安装前，应首先明确施工范围，检查现场条件是否符合设计和施工图纸对墙体安装的要求，防火、防尘、防静电技术是否符合使用条件和有关规定。应参考以下方面：
（1）壁面、工作面与轴线之间的距离；
（2）根据基准面找出控制点的距离和位置，注意能见度；
（3）根据基准面找出安装角之间的距离；
（4）与控制高程的水平差；
（5）建筑物与各层之间的垂直距离。

要求防静电墙板接缝均匀、严密、无缝隙，机房墙面保持垂直角度。在墙体的垂直方向上，应尽量采用与墙体高度相同或尺寸较长的机房墙板，尽量减少墙体的搭接，使其紧贴墙面，对机房的安全美观起着重要作用。

I. characteristics of color steel plate

1. The machine room color steel plate is composed of 0.6mm hot-dip galvanized steel plate and 12mm fire-resistant gypsum inner decorative plate. The machine room color steel plate facing is multi-component polyester hardening coating, including conductive components. By increasing the conductivity and decreasing the static load, the surface resistance is 105-8, and the charge decay is less than 1 second. With the electrostatic paint spraying process, the surface is smooth, delicate, dust-free and easy to maintain, which greatly ensures the cleaning requirements of the machine room.

2. The color steel plate of the machine room conforms to the first level fire protection standard of the national standard, and fully meets the fire protection requirements of the construction and decoration of the machine room.

3. The machine room color steel plate surface is color steel plate, moisture-proof, mildew proof, acid and alkali resistant, anti-static. At 500Hz, the sound insulation rate can reach 45dB (the noise generated by 500Hz is generally 118db), and the improvement of weighted sound insulation is quite high.

4. The color steel plate in the machine room has high porosity, all of them are micropores, small thermal conductivity [generally 0.121 ~ 0.205w / (m.k)), large heat capacity and strong moisture absorption, which has a certain effect on regulating indoor temperature.

5. The color steel plate compartment system of the machine room meets the requirements of cns12514-5kg drop impact test and has strong impact resistance.

6. The installation cycle of color steel plate in the machine room is short and the site is clean, which saves precious construction time for the whole project. The color steel plate in the machine room can be disassembled and repaired, which is convenient for disassembly, water and electricity maintenance, line transformation, etc.

7. It can drill holes in the color steel plate wall of the machine room without additional treatment. It is very convenient to install control switch, power socket and other equipment. The surface color is soft, forming a unified and harmonious whole with the floor and ceiling, so that the whole space has a modern flavor

What is the role of color steel plate in the construction of computer room?

Two. Use place of color steel plate

A. office buildings of national ministries and commissions; government agencies; computer centers of banking, insurance, securities and other financial institutions; high-end office buildings.

B. public space Hospital; school; Scientific Research Institute; civil aviation, subway and other transportation stations.

C. industrial building standardized industrial plant; food, drug, chemical and other plants; professional laboratory or R & D center.

D. commercial space exhibition center; sports venues; star hotels

The following points should be paid attention to when installing the wall panel of the machine room

1. Special tools shall be used for the installation of the wall panel of the machine room, and the construction personnel shall use them during the construction

Before inspection, check whether the tools are complete. The specific work of inspection is whether the main materials and accessories are complete and can be used. Special measuring tools shall be customized after inspection. If it does not meet the use requirements, it shall be replaced and repaired in a timely manner.

2. Before installation, the construction scope shall be defined first, and the site conditions shall be checked to see whether they meet the requirements of the design and construction drawings for wall installation, and whether the fire-proof, dust-proof and anti-static technologies meet the use conditions and relevant regulations. Reference should be made to the following:

(1) the distance between the wall, working face and axis;

(2) find out the distance and position of the control point according to the datum, and pay attention to the visibility;

(3) find out the distance between the installation angles according to the datum plane;

(4) the horizontal difference with the control elevation;

(5) the vertical distance between the building and each floor.

It is required that the joints of the anti-static wallboard shall be even, tight and seamless, and the wall of the machine room shall keep a vertical angle. In the vertical direction of the wall, the wall board of the machine room with the same height or long size as the wall should be used as far as possible, so as to minimize the overlap of the wall and make it close to the wall, which plays an important role in the safety and beauty of the machine room.