如何加强彩涂板的防火性？
天物彩板专注彩涂板行业16年——更多如何加强彩涂板的防火性？_防火彩钢板生产厂家请拨打网站上方电话咨询
事实上，耐火性也是一个非常重要的性能。虽然彩钢板的这一特性不是很显著，但我们可以帮助它在后期实现耐火性。让我们来看看如何增强彩涂板的耐火性。
1、采用耐火性能好的岩棉作为彩涂板的芯材，是根本解决方案。
2.施工时，芯材应远离电焊、气焊等明火作业；
3.在使用过程中，一些热源和火源不应靠近彩涂板，并应保持一定的距离。河南彩钢板房如果要设置厨房，需要设置保温层，墙面应设置防火岩棉保温层；
4.电线电缆最好不要与芯材交叉。如有必要，应增加保护套。插座、开关箱采用金属镀锌箱及表面安装方式；
5、室内外均应配备简易消防器材。如有可能，应配备火灾报警器，以便于人员快速疏散；
6.彩色涂层板之间至少保持6米的安全距离。河南彩钢板房的层间填充材料未经严格阻燃处理，虽为易燃材料，但不会自燃。
彩涂板经过表面处理后，需要对彩涂板进行涂装，以满足颜色要求，达到防腐效果。然而，油漆对环境有特殊要求，如下所示：
1.尽量避免在阳光直射或灰尘多的地方施工彩色涂层板。
2.工作环境应清洁、干燥、通风。环境温度在5℃以上，相对湿度在85%以下，方可施工。若超过限值，应立即采取措施，否则不得施工。
3、彩涂板室外施工时，遇雨、雾、露或表面潮湿时，应停止施工。
4.避免在强风中工作；在炎热天气下工作时，应避免冷却气流的影响。在这种环境下工作时，只能使用刷子来防尘。
5、严禁湿表面涂装；露点温度取决于环境相对湿度和空气温度的组合。
In fact, fire resistance is also a very important performance. Although this characteristic of color steel plate is not very significant, we can help it achieve fire resistance in the later stage. Let's see how to strengthen the fire resistance of Henan
color coated board.
1。 Rock wool with good fire resistance can be used as the core material of color coated board, which is the fundamental solution.
2. During construction, the core material shall be kept away from open flame operations such as electric welding and
gas welding;
3. During use, some heat sources and fire sources should not be close to the color coated plate, and a certain distance should be maintained. If you want to set up a kitchen in Henan color steel board room, you need to set up an insulation
layer, and the wall should be set with fireproof rock wool insulation layer;
4. Wires and cables are better not to cross from the core material. If necessary, protective sleeves shall be added. Socket and switch box shall adopt metal galvanized
box and surface installation method;
5. Simple fire-fighting equipment shall be equipped indoors and outdoors. If possible, fire alarm shall be equipped to facilitate rapid evacuation of personnel;
6. Keep a safe distance of at least 6m between
color coated plates. Although the interlayer filling material of Henan color steel slab house without strict flame retardant treatment is flammable, it will not spontaneously ignite.
After the surface treatment of the color coated plate, the color
coated plate needs to be coated to meet the color requirements and achieve the anti-corrosion effect. However, painting has special requirements for the environment, as follows:
1。 Try to avoid the construction of color coated plates in direct sunlight
or dusty places.
2。 The working environment shall be clean, dry and ventilated. Construction can only be carried out when the ambient temperature is above 5 ℃ and the relative humidity is below 85%. If any limit value is exceeded, measures shall
be taken immediately, otherwise construction is not allowed.
3。 During outdoor construction of color coated plate, the construction shall be stopped in case of rain, fog, dew or wet surface.
4。 Avoid working in strong winds; When working in
hot weather, avoid the influence of cooling air flow. When working in such an environment, only brush can be used to prevent dust.
5. Wet surface coating is strictly prohibited; The dew point temperature depends on the combination of ambient relative
humidity and air temperature.
