唐山天物彩板有限公司

天物彩板 · 专注定制彩板16年
资讯详情
印花彩钢板屋面渗漏怎么办

 印花彩钢板屋面渗漏怎么办

天物彩板专注彩板行业16年——印花彩钢板报价请拨打网站上方电话咨询

山东印花彩钢板厂家屋面渗漏怎么办_天物彩板

彩色钢板印刷广泛应用于建筑行业。彩色钢板印刷在我们的生活中很常见。你知道印刷彩钢板屋顶漏水的解决办法吗?我们来看看彩印钢板屋面渗漏的解决办法。
印刷彩钢板改变了以砖、瓦、灰、石为主要材料的建材格局,出现了钢彩钢结构建筑。这种建筑结构的出现使电厂汽轮机车间、汽车制造业、飞机制造业、大型车间、大型超市、物流仓库等得到了广泛的应用。该建筑结构的最大优点是工期短、建筑材料轻、地基要求低、跨度大、室内空间大、使用方便等,但也存在一些问题,主要问题是:屋面、铆钉、板节点都有渗漏,影响正常使用。
彩钢印刷板屋面渗漏的解决办法:
1、 铆钉漏水的维修方法:
阳光2000Pa单组分防水胶涂刷4遍,厚度约1.5mm,直径约Φ60mm。下一次涂刷的涂料不应粘手,下一次涂刷的涂料直径应比第一次涂刷的直径大Φ15mm,中厚圆内较薄。
2、 接缝漏水修补方法:
一。小缝修补方法:
① 接缝两端可采用单组分防水胶,宽度为60mm,日照为2000Pa,相邻接缝处不采用宽度为20mm的防水胶。
② 无纺布(或玻璃纤维布),宽150 mm,粘贴在涂有阳光的2000Pa防水胶上。
③ 在无纺布或玻璃纤维布上刷三次。最后一块的宽度比前一块宽50毫米,厚度约为1.8毫米。后道涂料应多次涂刷,不得粘手。
2。板接头大修理方法:
① 可填充dm-600密封胶Pu
② 接缝两端涂60mm宽日光2000Pa单组分防水胶,接缝附近不涂20mm。
③ 无纺布或玻璃纤维布,150 mm宽,粘贴在涂有阳光的2000帕防水粘合剂上。
④ 在粘贴的布上刷三遍阳光2000Pa单组分防水胶。刷涂时,第二层宽度应比前一层宽50 mm,厚度约为1.8 mm。第二道漆的厚度应为中间漆的厚度,两边的厚度应薄,后一道漆不得粘手。阳光2000Pa单组分防水胶,距接缝20 mm不涂。
⑤ 无纺布或玻璃纤维布,150 mm宽,粘贴在涂有阳光的2000帕防水粘合剂上。
⑥ 在粘贴的布上刷三遍阳光2000Pa单组分防水胶。刷涂时,第二层宽度应比前一层宽50 mm,厚度约为1.8 mm。第二道漆的厚度应为中间漆的厚度,两边的厚度应薄,后一道漆不得粘手。

Printing color steel plate is widely used in the construction industry. Printing color steel plate is quite common in our life. Do you know the solution to the leakage of printing color steel plate roof? Let's look at the solution to the leakage of the printed color steel plate roof.

Printed color steel plate has changed the pattern of building materials with brick, tile, ash and stone as the main materials, and steel color plate structure buildings have emerged. The appearance of this building structure makes the power plant steam turbine workshop, automobile manufacturing industry, aircraft manufacturing industry, large-scale workshop, large-scale supermarket, logistics warehouse and so on widely used. The biggest advantages of this building structure are short construction period, light building materials, low foundation requirements, large span, large indoor space, easy to use, etc. But there are also some problems, the main problem is: the roof, rivets, board joints have leakage, affecting the normal use.
Solutions to the leakage of printed color steel sheet roof:
1、 Maintenance method of water leakage at rivet:
The sunlight 2000Pa single component waterproof adhesive shall be applied for 4 times, with a thickness of about 1.5mm and a diameter of about Φ 60mm. The coating applied for the next time shall not stick to the hand, and the diameter of the coating applied for the next time shall be Φ 15mm larger than that applied for the first time, which is thin in the middle thick circle.
2、 Repair method of water leakage at joint:
1. Small joint repair method:
① One component waterproof adhesive with a width of 60mm and a sunlight of 2000Pa can be applied at both ends of the joint, and the joint adjacent to the joint is not applied with a width of 20mm.
② Non woven fabric (or glass fiber cloth), 150 mm wide, pasted on 2000Pa waterproof adhesive coated with sunlight.
③ Brush on the non-woven fabric or glass fiber cloth for three times. The width of the last one is 50 mm wider than the previous one and the thickness is about 1.8 mm. The later coating shall be applied more than one time without sticking hands.
2. Large repair method of plate joint:
① It can be filled with dm-600 sealer Pu sealant
② Apply 60mm wide sunlight 2000Pa single component waterproof adhesive at both ends of the joint, and do not apply 20mm adjacent to the joint.
③ Nonwoven or glass fiber cloth, 150 mm wide, pasted on 2000Pa waterproof adhesive coated with sunlight.
④ Brush three times of sunlight 2000Pa single component waterproof adhesive on the pasted cloth. When brushing, the width of the second coat shall be 50 mm wider than that of the previous one, and the thickness shall be about 1.8 mm. The thickness of the second coat shall be the thickness of the middle coat and the thickness of both sides shall be thin, and the later coat shall not stick to the hand. Sunlight 2000Pa single component waterproof adhesive, 20 mm adjacent to the joint is not applied.
⑤ Nonwoven or glass fiber cloth, 150 mm wide, pasted on 2000Pa waterproof adhesive coated with sunlight.
⑥ Brush three times of sunlight 2000Pa single component waterproof adhesive on the pasted cloth. When brushing, the width of the second coat shall be 50 mm wider than that of the previous one, and the thickness shall be about 1.8 mm. The thickness of the second coat shall be the thickness of the middle coat and the thickness of both sides shall be thin, and the later coat shall not stick to the hand.
返回列表
上一篇
下一篇