彩钢夹芯板安装及特点

彩钢夹芯板安装
彩钢夹芯板安装时，抬板是常见的，但搬运也很特殊，两端同时要小心抬起。这将防止损坏其表面氧化膜。安装墙板时，最好一次抬起一块墙板。治具要选择专用治具，一般厂家都会有这样的治具。吊装应缓慢进行，避免磕碰。

对于夹芯板的固定，有两种方法：我们可以用自攻螺钉穿过墙板，这样就可以直接固定在墙体底座上。我们也可以用自攻螺钉通过连接件间接与墙体底座连接。幕墙板安装精度一般规定为：立面垂直度2mm，表面平整度3mm。另外，接头的直线度为0.5mm，安装必须按厂家规定进行。
在安装时，还需要使用耐候胶。这通常是固定在一些边缘板和泛水板将使用。注意采用耐候胶嵌缝密封，保持其密封性，使其能有效防止空气渗透和雨水渗漏。
安装结束后，我们需要检查。一般情况下，彩钢夹芯板幕墙安装完成后，需要将墙板表面的保护胶带自上而下逐层揭下，并将框架逐层拆除。注意不要刮伤或碰伤墙板。检查并清理一些粘结剂和灰尘，以保持整个施工的完整性。
彩钢夹芯板的特性
1重量轻，每平方米不到14公斤，可充分减轻结构荷载，降低结构造价。
2复合板安装速度快、重量轻、拼接安装、随意切割决定了其安装简单，可大大提高效率，节省工期。
三。防火，彩色复合夹芯板的面层材料和保温材料均为不燃材料，完全符合防火规范的要求。

Installation of color steel sandwich panel

During the installation of color steel sandwich plate, it is common to carry the plate, but the handling is also particular, and both ends should be raised carefully at the same time. This will prevent damage to its surface oxide film. When installing the wall panel, it is better to lift one panel at a time. Fixture to choose a special fixture, general manufacturers will have such a fixture. Hoisting should be carried out slowly to avoid some bumps.
For the sandwich panel fixation, there are two ways: we can use self tapping screws through the wall panel, in this way to directly fix on the wall substructure. We can also use self tapping screws through connectors to indirectly connect with the wall substructure in this way. Generally, the installation accuracy of curtain wall panel is regulated as follows: its elevation perpendicularity is 2mm, and its surface flatness is 3mm. In addition, the straightness of the joint is 0.5mm, and the installation must be carried out according to the manufacturer's regulations.
In the installation, also need to use weather resistant glue. This is usually fixed in some edge plate and flashing board will be used. Pay attention to the use of weather resistant glue caulking seal to maintain its tightness, so that it can effectively prevent air permeability and rainwater leakage.
At the end of the installation, we need to check. Generally, after the installation of the color steel sandwich panel curtain wall is completed, we need to remove the protective adhesive tape on the surface of the wallboard layer by layer from top to bottom, and dismantle the frame layer by layer. Take care that the wall panel is not scratched or bruised. Check and clean some binders and dust to keep the integrity of the whole construction.
Characteristics of color steel sandwich panel
1. Light weight, less than 14kg per square meter can fully reduce the structural load and reduce the structural cost.
2. Quick installation, light weight of the composite plate, splicing installation and cutting at will determine its simple installation, which can greatly improve efficiency and save construction period.
3. Fireproof, the surface material and thermal insulation material of color composite sandwich panel are non combustible materials, which can fully meet the requirements of fire protection code.